Regviz

Alif Semiconductor /AE512F80F55D5AS_CM55_HE_View /LPUART /UART_LCR_EXT

Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text

Interpret as UART_LCR_EXT

Share

Cut and paste this URL to share the unmodified register and value:

https://regviz.com/r/Alif Semiconductor/AE512F80F55D5AS_CM55_HE_View/LPUART/UART_LCR_EXT#0x0

31 2827 2423 2019 1615 1211 87 43 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 (DLS_E)DLS_E 0 (Val_0x0)ADDR_MATCH 0 (Val_0x0)SEND_ADDR 0 (Val_0x0)TRANSMIT_MODE

TRANSMIT_MODE=Val_0x0, SEND_ADDR=Val_0x0, ADDR_MATCH=Val_0x0

Description

Line Extended Control Register

Fields

DLS_E

Extension for DLS This bit is used to enable 9-bit data for transmit and receive transfers.
ADDR_MATCH

This bit is used to enable the address match feature during Receive mode. This bit is applicable only when UART_LCR_EXT[DLS_E] is set to 1.

0 (Val_0x0): Normal mode. The UART will start to receive the data and 9-bit character will be formed and written into the receive Rx FIFO. Then read the data and differentiate address and data.

1 (Val_0x1): Address match mode. The UART will wait until the incoming character with 9^th bit set to 1 and further checks to see if the address matches with what is programmed in UART_RAR register. If match is found, then sub-sequent characters will be treated as valid data and UART starts receiving data.
SEND_ADDR

This bit is used as a control knob to determine when to send the address during Transmit mode. This bit is auto-cleared, after sending out the address character. This field is applicable only when UART_LCR_EXT[DLS_E] bit is set to 1 and UART_LCR_EXT[TRANSMIT_MODE] is set to 0.

0 (Val_0x0): 9-bit character will be transmitted with 9^th bit set to 0 and the remaining 8-bits will be taken from the Tx FIFO which is programmed through 8-bit wide UART_THR/UART_STHR registers.

1 (Val_0x1): 9-bit character will be transmitted with 9^th bit set to 1 and the remaining 8-bits will match to what is being programmed in UART_TAR register.
TRANSMIT_MODE

This bit is used to control the type of Transmit mode during 9-bit data transfers. Address: 9^th bit set to 1; Data: 9^th bit set to 0. Note: The UART_TAR[TAR] field is not applicable in this mode of operation.

0 (Val_0x0): In this mode of operation, UART_THR[THR] field and from UART_STHR0[STHRN] to UART_STHR15[STHR15] fields are 8-bit wide. Program the address into UART_TAR[TAR] field and data into the UART_THR/UART_STHR registers. The UART_LCR_EXT[SEND_ADDR] bit is used as a control knob to indicate the UART on when to send the address.

1 (Val_0x1): In this mode of operation, UART_THR[THR] field and from UART_STHR0[STHRN] to UART_STHR15[STHR15] fields are 9-bit wide.

Links

()

Register License

THIS SOFTWARE IS PROVIDED “AS IS”. NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. ALIF SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.

 ()

Register Reference

https://github.com/cmsis-svd/cmsis-svd-data